Solved: I have developed a very simple code to acquire data from a NI DAQ in LabView and it works just fine on my desktop. But whenever I try. The multiuser MAC layer enhancements to the 802.11 Application Framework to go beyond the PHY layer to address complex network-level problems that will arise for 5G system development. One example of this is 5G network slicing across different radio access technologies. Wireless researchers can pair the 802.11 Application Framework with NI software defined radio hardware to rapidly conduct network-level, real-time, over-the-air prototyping experiments for a wide range of WiFi and 5G MAC/PHY research. The 802.11 Application Framework also supports up to 80MHz of real-time bandwidth and full bidirectional communications and includes MAC layer features including CSMA/CA, RTS, CTS, NAV and retransmission. Hello I have a VeriStand-Project (VSP) created with my Laptop-Host (LTH) which works with my PXI, while deploying it from my LTH. Then I have installed the whole NI enviroment for PXI and VeriStand use on a industrial PC (iPC). I have tried to deploy my VSP from the iPC to the PXI but the following error message arose on my iPC: The VeriStand Gateway encountered an error while deploying the System Definition file. Details: Error - occurred at Project Window.lvlib:Project Window.vi >> Project Window.lvlib:Command Loop.vi >> NI_VS Workspace ExecutionAPI.lvlib:NI VeriStand - Connect to System.vi Possible reason(s): NI-XNET: (Hex 0xBFF63147) The database information on the real-time system has been created with an older NI-XNET version. This version is no longer supported. To correct this error, re-deploy your database to the real-time system. ========================= NI VeriStand: NI VeriStand Engine.lvlib:VeriStand Engine Wrapper (RT).vi >> NI VeriStand Engine.lvlib:VeriStand Engine.vi >> NI VeriStand Engine.lvlib:VeriStand Engine State Machine.vi >> NI VeriStand Engine.lvlib:Initialize Inline Custom Devices.vi >> Custom Devices Storage.lvlib:Initialize Device (HW Interface).vi * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * • Unloading System Definition file. • Connection with target Controller has been lost. The software versions of the NI products (MAX/My System/Software) between my LTH and the iPC are almost the same. The only differences are: 1. LabView Run-Time 2009 SP1 (64-bit); is installed on LTH but missing on iPC 2. LabView Run-Time 2012 f3; is installed on LTH but missing on iPC 3. NI-DAQmx ADE Support 9.3.5; something strage on the LTH, because normally I am using NI-DAQmx 9.5.5 and all other DAQmx products on my LTH are 9.5.5. That means NI-DAQmx Device Driver 9.5.5 and NI-DAQmx Configuration 9.5.5. On the iPC side all three products are 9.5.5. That means NI-DAQmx ADE Support 9.5.5, NI-DAQmx Device Driver 9.5.5 and NI-DAQmx Configuration 9.5.5. Traditional NI-DAQ 7.4.4; The iPC has this SW installed. On the LTH this SW is missing. In order to fix this problem I have formatted my PXI and I have installed the following SW from the iPC: 1. LabVIEW Real-Time 11.0.1 2. ![]() NI-488.2 RT 3.0.0 3. NI_CAN 2.7.3 Unfortunately the above stated problem arose. What can I do to fix this problem? I found a hint on There it is written to deploy the dbc file againt. If this is a good hint, so how do I deploy a dbc file? I would feel very pleased if somebody could help me!:-) Best regards Lukas Nowak.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |